|
|
|
|
|
|
BIRDCAGE BRACKET 1/8' STEEL 5/8 HOLE
|
|
|
BIRDCAGE BRACKET FITS 3 1/2" TUBING 2 3/4" RADIUS TO CENTER OF HOLE
1/8 THICK
5/8 HOLE
SOLD EACH
|
|
|
|
|
|
|
|
|
|
BIRDCAGE BRACKET 3/16' STEEL 1/2 HOLE SHOCK TAB
|
|
|
BIRDCAGE BRACKET FITS 3 1/2" TUBING 2 3/4" RADIUS TO CENTER OF HOLE
3/16 THICK
1/2 HOLE
SOLD EACH
|
|
|
|
|
|
|
|
|
|
BIRDCAGE BRACKET 3/16' STEEL 5/8 HOLE
|
|
|
BIRDCAGE BRACKET FITS 3 1/2" TUBING 2 3/4" RADIUS TO CENTER OF HOLE
3/16 THICK
5/8 HOLE
SOLD EACH
|
|
|
|
|
|
|
|
|
|
Link Tabs 3" radius for rear end housing 3/8" thick Tall
|
|
|
3/8" thick
4 3/4" tall
9/16" hole
2 5/8" stand off
Price is for one tab
|
|
|
|
|
|
|
|
|
|
Link Tabs 3" radius for rear end housing 3/8" thick
|
|
|
3/8" thick
3 3/4" tall
9/16" hole
2" stand off
Price is for one tab
|
|
|
|
|
|
|
|
|
|
REAR END BRACKET
|
|
|
SOLD EACH
REAR END BRACKET-SOLD EACH 3/16 STEEL 1/2 HOLE - SHOCK MOUNT, LIMIT STRAP, 4 LINK AIR RIDE
|
|
|
|
|
|
|
|
|
|
FABRICATOR CHASSIS LINK TAB, FLAT BOTTOM, 3/8 THICK
|
|
|
- These are the ideal way to set up the bottom link of any 3 or 4 link suspension but to call these Tabs is just a little bit off the mark.
They are meant for the bottom of the rig, the side taking a beating now and then (all the time).
We make them .385 thick and with a sloped shape to survive everything you can throw at em', we are pretty sure you can wear them out but you will be very challenged to break them. - They are high enough around the bolt to give all but the very largest Heims complete protection and still short enough on the joint end to allow full articulation. These also make an excellent Ram mount off of a truss.
Made exclusively of A50 Steel Plate for its density and strength.
These are sold EACH.-
7 3/4" LONG - 3 1/4 TOTAL HEIGHT
- 1 3/4 CENTER HOLE TO BASE
- 9/16 HOLE COULD BE DRILLED OUT LARGER
|
|
|
|
|
|
|
|
|
|
Link Mounts for flat surface
|
|
|
1/4" thick
3 3/16" tall
9/16" hole
1 5/8" stand off
2 5/8" opening for rod end
4 3/4"x3 1/2" pad needed for welding
Price is for the pair
|
|
|
|
|
|
|
|
|
|
Centered Axle Panhard Bracket
|
|
|
Panhard / Trackbar bracket. It has 3 mounting position options, 5.5", 6'5", & 7.5" from Axle center. They are cut to a 3" axle tube radius so they can be made to fit any tube diameter, made from 1/4" plate These are setup for a 2" ID so just about any heim will fit with minimal misalignment. 9/16" holes.
I.D. of bracket is 2" and drilled for 9/16 bolts
|
|
|
|
|
|
|
|
|
|
Link Mounts Radiused for rear end housing
|
|
|
1/4" thick
3" wide
4" tall
9/16" hole
2 1/8" stand off
2 5/8" opening for rod end
Price is for the pair
|
|
|
|
